1、 三菱 C6C64C64T 三菱 C6C64C64T 編程說明書 (M系)
在ISO 碼中，從控制出“（”起至控制入“）”（或“；”）止的所有信息均被視為無效。 定顯示裝置。因此，可在此間輸入與指令紙帶的名稱編號等控制沒有直接關系的信息。 但是，紙帶存儲時此間的信息（“紙帶碼一覽表”的（B）除外）也被存儲。 電源接通時為控制入狀態。
在ISO 碼中，從控制出“（”起至控制入“）”（或“；”）止的所有信息均被視為無效。 定顯示裝置。因此，可在此間輸入與指令紙帶的名稱編號等控制沒有直接關系的信息。 但是，紙帶存儲時此間的信息（“紙帶碼一覽表”的（B）除外）也被存儲。 電源接通時為控制入狀態。
2、 三菱 C6C64C64T 三菱 C6C64C64T 編程說明書 (M系)
(1) Address check This function enables simple checking of progr am addresses in word units. If the alphabetic characters are continuous, the program error (P32) will occur. Availability of t
(1) Address check This function enables simple checking of progr am addresses in word units. If the alphabetic characters are continuous, the program error (P32) will occur. Availability of t
3、 三菱 C6C64C64T 三菱 C6C64C64T 編程說明書 (M系)
For items described in "Restrictions" or "Usable State", the instruction manual issued by the machine manufacturer takes precedence over this manual. An effort has been made to note as man
For items described in "Restrictions" or "Usable State", the instruction manual issued by the machine manufacturer takes precedence over this manual. An effort has been made to note as man
4、三菱 C6C64C64T 三菱 C6C64C64T 參數說明書
(1) Word and address A word is a collection of characters arranged in a specific sequence. This entity is used as the unit for processing data and for causing the machine to execute specifi
(1) Word and address A word is a collection of characters arranged in a specific sequence. This entity is used as the unit for processing data and for causing the machine to execute specifi
5、三菱 C6C64C64T 三菱 C6C64C64T 參數說明書(eng).pdf
Set up a compensation factor for reducing a control error in the reduction of a corner roundness and arch radius. Indicates a maximum control error (mm) in parentheses. The larger the
Set up a compensation factor for reducing a control error in the reduction of a corner roundness and arch radius. Indicates a maximum control error (mm) in parentheses. The larger the
6、三菱 C6C64C64T 三菱 C6C64C64T 連接維護說明書
Correctly connect the output side (terminal U, V, W). The servomotor will not run properly if incorrectly connected. Always install an AC reactor per each power supply unit. Alw
Correctly connect the output side (terminal U, V, W). The servomotor will not run properly if incorrectly connected. Always install an AC reactor per each power supply unit. Alw
7、三菱 C6C64C64T 三菱 C6C64C64T 使用說明書
If the tool compensation amount is changed during automatic operation (including single block stop), the amount will be validated from the next block or several blocks following. If the
If the tool compensation amount is changed during automatic operation (including single block stop), the amount will be validated from the next block or several blocks following. If the
8、三菱 C6C64C64T 三菱 C6C64C64T 網絡使用說明書.pdf
For items described as "Restrictions" or "Usable State" in this manual, the instruction manual issued by the machine maker takes precedence over this manual. Items not described in th
For items described as "Restrictions" or "Usable State" in this manual, the instruction manual issued by the machine maker takes precedence over this manual. Items not described in th
9、三菱 C70系列 三菱 C70系列 PLC接口說明書
Incorrect connections may damage the devices, so connect the cables to the specified connectors. When connecting to a personal computer and a unit with the RS-232/USB interface, an electric
Incorrect connections may damage the devices, so connect the cables to the specified connectors. When connecting to a personal computer and a unit with the RS-232/USB interface, an electric
10、三菱 C70系列 三菱 C70系列,編程說明書(M系)
(1) 執行主軸同期時，必須同時對基準主軸和同期主軸發出旋轉指令。但是，同期主軸的旋轉方向與正反轉指 令無關，而是取決于基準主軸的旋轉方向和主軸同期旋轉方向。 (2) 在主軸轉速指令為ON的狀態下，接通主軸同期控制信號，雖然會進入主軸同期控制模式，但是不會進行 實際的同期控制。向基準主軸發出轉速指令之后才會進行同期控制，輸出主軸同期完成信號。 (3) 主軸同期控制下正
(1) 執行主軸同期時，必須同時對基準主軸和同期主軸發出旋轉指令。但是，同期主軸的旋轉方向與正反轉指 令無關，而是取決于基準主軸的旋轉方向和主軸同期旋轉方向。 (2) 在主軸轉速指令為ON的狀態下，接通主軸同期控制信號，雖然會進入主軸同期控制模式，但是不會進行 實際的同期控制。向基準主軸發出轉速指令之后才會進行同期控制，輸出主軸同期完成信號。 (3) 主軸同期控制下正
11、三菱 C70系列 三菱 C70系列 規格說明書 -英
The items that are not described in this manual must be interpreted as "not possible". This manual is written on the assumption that all option functions are added. Some fu
The items that are not described in this manual must be interpreted as "not possible". This manual is written on the assumption that all option functions are added. Some fu
12、 三菱-70系列 三菱-70系列 設定說明書(Eng)
Set a compensation coefficient for reducing a control error in the reduction of a corner roundness and arch radius. The larger the setup value, the smaller the theoretical error will be . Ho
Set a compensation coefficient for reducing a control error in the reduction of a corner roundness and arch radius. The larger the setup value, the smaller the theoretical error will be . Ho
